SIMULATION STUDY TO VERIFY THE EFFECT OF CUTTING PARAMETERS ON CHIP SHINKEGE COEFICIENT DURING MACHINING PROCESS OF ALUMINUM ALLOY

  • Pham Thi Hoa Hung Yen University of Technology and Education
  • Nguyen Duc Toan Hung Yen University of Technology and Education
Keywords: Chip shrinkage coefficient, the Bao-Wierzbicki fracture model, modified Mohr-Coulomb criteria, A6061 aluminum alloy, simulation of the cutting process

Abstract

This paper presents a numerical study on parameters of the chip produced in high-speed milling of aluminum alloy considering the effect of cutting depth and speed. First, a finite element model was created by the ABAQUS / Explicit finite element simulation software, based on the Bao-Wierzbicki (B-W) fracture model with a modified Mohr-Coulomb criterion. The model verification was made by comparing the simulated chip thickness to that obtained by theoretical formulae. Then, the effect of cutting depth and speed on the chip thickness, chip shrinkage coefficient and shear angle of the chip were investigated. The simulation results showed that the chip thickness reduced with increasing cutting speed. In addition, increasing cutting speed or cutting depth reduces the chip shrinkage coefficient, but increases the shear angle of chip

References

T. Data, “Fracture Characteristics of Three Matals Subjected to Various Strains, Strain Rates, Temperature and Perssures,” Eng. Mech., vol. 21, no. I, 1985.

M. S. Swan, “Incorporation of a General Strain-to - failure Fracture Criterion into a Stress based Plasticty Model through a Time to Failure by,” Thesis Mech. Eng. - Univ. Utah, USA., no. May, 2012.

O. Article, “On Predicting Chip Morphology and Phase Transformation in Hard Machining,” Int Adv Manuf Technol, pp. 645–654, 2006.

J. Shi and C. R. Liu, “Flow Stress Property of a Hardened Steel at Elevated Ttemperatures with Tempering e ect,” Int. J. Mech. Sci., vol. 46, pp. 891–906, 2004.

M. L. Wilkins, R. D. Streit, and J. E. Reaugh, “Cumulative-Strain-Damage Model of Ductile Fracture: Simulation and Prediction of Engineering Fracture Tests,” Lawrence Livermore Natl.

Lab., pp. 1–68, 1980.

D. J. L. M.G.Cockcroft, “Ductility and the Workability of Metals .pdf.” p. J Inst Metals, 1968. [7]. E. Ceretti, M. Lucchi, and T. Altan, “FEM Simulation of Orthogonal Cutting: Serrated Chip Formation,” Juornal Mater. Process. Technol., vol. 95, pp. 17–26, 1999.

J. Lorentzon, N. Järvstråt, and B. L. Josefson, “Journal of Materials Processing Technology Modelling Chip Formation of Alloy 718,” J. Mater. Process. Technol., vol. 209, pp. 4645–4653, 2009. [9]. A. Gilioli, A. Manes, M. Giglio, and T. Wierzbicki, “Predicting Ballistic Impact Failure of Aluminium 6061-T6 with the Rate-independent Bao-Wierzbicki Fracture Model,” International Journal of Impact Engineering, vol. 76. pp. 207–220, 2015.

M. Giglio, A. Manes, and F. Viganò, “Numerical Simulation of the Slant Fracture of a Helicopter’s Rotor Hub with Ductile Damage Failure Criteria,” Fatigue Fract. Eng. Mater. Struct., vol. 35, no. 4, pp. 317–327, 2012.

R. Stringfellow and C. Paetsch, “Modeling Material Failure During Cab Car End Frame Impact,” in 2009 Joint Rail Conference, 2009, pp. 183–192.

X. Teng and T. Wierzbicki, “Effect of Fracture Criteria on High Velocity Perforation of Thin Beams.,” Int. J. Comput. Methods, vol. 1, no. 1, pp. 171–200, Jun. 2004.

H. Z. Li and J. Wang, “A Cutting Fforces Model for Milling Inconel 718 Alloy based on A Material Constitutive Law,” Proc. Inst. Mech. Eng. Part C J. Mech. Eng. Sci., vol. 227, no. 8, pp. 1761–1775, 2013.

Y. Chen, H. Li, and J. Wang, “Analytical Modelling of Cutting Forces in Near-orthogonal Cutting of Titanium Alloy Ti6Al4V,” Proc. Inst. Mech. Eng. Part C J. Mech. Eng. Sci., vol. 229, no. 6, pp. 1122–1133, 2015.

M. H. Ali, B. a. Khidhir, M. N. M. Ansari, and B. Mohamed, “FEM to Predict the Effect of Feed Rate on Surface Roughness with Cutting Force during Face Milling of Titanium Alloy,” HBRC J., vol. 9, no. 3, pp. 263–269, 2013.

X. Cui, B. Zhao, F. Jiao, and J. Zheng, “Chip Formation and its Effects on Cutting Force, Tool Temperature, Tool Stress, and Cutting Edge Wear in High- and Ultra-high-speed Milling,” Int. J.

Adv. Manuf. Technol., vol. 83, no. 1–4, pp. 55–65, 2016.

A. Davoudinejad, E. Chiappini, S. Tirelli, M. Annoni, and M. Strano, “Finite Element Simulation and Validation of Chip Formation and Cutting Forces in Dry and Cryogenic Cutting of Ti-6Al4V,” Procedia Manuf., vol. 1, pp. 728–739, 2015.

D. Xu, P. Feng, W. Li, and Y. Ma, “An Improved Material Constitutive Model for Simulation of High-speed Cutting of 6061-T6 Aluminum Alloy with High Accuracy,” Int. J. Adv. Manuf. Technol., vol. 79, no. 5–8, pp. 1043–1053, 2015.

M. Bäker, “Finite Element Simulation of High-speed Cutting Forces,” J. Mater. Process. Technol., vol. 176, no. 1–3, pp. 117–126, 2006.

J. P. Davim, C. Maranhão, M. J. Jackson, G. Cabral, and J. Grácio, “FEM Snalysis in High Speed Machining of Aluminium Alloy (Al7075-0) using Polycrystalline Diamond (PCD) and Cemented Carbide (K10) Cutting Tools,” Int. J. Adv. Manuf. Technol., vol. 39, no. 11–12, pp. 1093–1100, 2008.

M. H. Ali, B. a. Khidhir, B. Mohamed, and a. a. Oshkour, “Prediction of High Cutting Speed Parameters for Ti-6Al-4V by Using Finite Element Modeling,” Int. J. Model. Optim., vol. 2, no. 1, pp. 31–35, 2012.

Y. Bai and T. Wierzbicki, “Application of extended Mohr-Coulomb Criterion to Ductile Fracture,” Int. J. Fract., vol. 161, no. 1, pp. 1–20, 2010.

Y. Li, T. Wierzbicki, M. A. Sutton, J. Yan, and X. Deng, “Mixed Mode Stable Tearing of Thin Sheet AI 6061-T6 Specimens: Experimental Measurements and Finite Element Simulations using a Modified Mohr-Coulomb Fracture Criterion,” Int. J. Fract., vol. 168, no. 1, pp. 53–71, 2011.

A. M. Beese, M. Luo, Y. Li, Y. Bai, and T. Wierzbicki, “Partially Coupled Anisotropic Fracture Model for Aluminum Sheets,” Eng. Fract. Mech., vol. 77, no. 7, pp. 1128–1152, 2010.

M. E. Merchant, “Mechanics of the Metal Cutting Process. I. Orthogonal Cutting and a Type 2 Chip,” J. Appl. Phys., vol. 16, no. 5, pp. 267–275, 1945.

Published
2017-10-11
How to Cite
Pham Thi Hoa, & Nguyen Duc Toan. (2017). SIMULATION STUDY TO VERIFY THE EFFECT OF CUTTING PARAMETERS ON CHIP SHINKEGE COEFICIENT DURING MACHINING PROCESS OF ALUMINUM ALLOY. UTEHY Journal of Science and Technology, 15, 16-21. Retrieved from http://tapchi.utehy.edu.vn/index.php/jst/article/view/157